陶瓷/薄钢板复合结构靶板抗高速侵彻性能研究

为探讨陶瓷/薄钢板复合结构靶板(ceramic/thin steel targets,CS靶板)的抗高速侵彻机理,通过弹道试验,分析了3 mm厚SiC陶瓷层和0.6 mm厚钢板层的CS靶板的破坏模式和抗侵彻性能,并与面密度基本相同的纯钢板进行了比较。在此基础上,基于能量守恒原理,建立了CS靶板抗高速侵彻的理论预测模型,并与试验结果进行了对比。结果表明,CS靶板中前陶瓷层的存在,使得后钢板层的破坏模式由剪切冲塞转变为花瓣开裂,大大提升了后钢板层的抗侵彻吸能效率,从而使得CS靶板的整体抗侵彻性能高于等面密度的纯钢板,CS靶板的整体抗侵彻效率较等面密度纯钢板提升15%以上;弹体穿透CS靶板后的剩余速度理论预测值与试验结果吻合较好,相对误差均在5%以内,验证了理论模型的合理性和有效性。     

火药复合焊条焊接接头的微观组织及性能

为提高战场装备的应急抢修能力,以火药和2Al/3CuO系高热剂为焊接热源,开发了一种新型的便携式焊接材料——火药复合焊条,对其焊缝的组织形貌及性能进行研究.试验结果表明,火药复合焊条的焊接属于熔化焊,焊缝与基体之间存在明显的过渡区,焊缝成形良好,焊缝的抗拉强度大于400MPa,高于母材本身强度,能够满足战场应急抢修能力的需要.     

球磨时间对纳米SiO_2/Cu复合材料摩擦学性能的影响

采用球磨法与热压烧结工艺制备了添加w（n-SiO2）=1.0%的铜基纳米复合材料。通过球盘式摩擦磨损试验机测试了复合材料的摩擦磨损性能,采用排水法和场发射扫描电镜（FSEM）研究了复合材料的致密度、显微组织和磨损形貌。结果表明：球磨可提高复合材料的致密度,改善n-SiO2在铜基体中的分散均匀性;随球磨时间的增加,复合材料的动摩擦因数和磨损量先减小后增加,球磨10 h复合材料具有较低的摩擦因数和磨损量,磨损机理主要为磨料磨损。     

陶瓷基复合装甲防12.7mm穿甲燃烧弹的靶试研究（Ⅱ）

基于对材料特性和防弹机理的认识,设计了由（SiC＋Si）陶瓷、616装甲钢和高强PE材料构成的陶瓷基复合靶板,靶板防护面密度为118 kg/m2,尺寸为500 mm×500 mm×25 mm。利用现役12.7 mm穿甲燃烧弹考核靶板在6发弹打击下的防护能力,检验靶板设计思路。结果表明：靶板结构是可行的,可防住V25为818 m/s的现役12.7 mm穿甲燃烧弹。     

Bending and stress analysis of polymeric composite plates reinforced with functionally graded graphene platelets based on sinusoidal shear-deformation plate theory

The bending and stress analysis of a functionally graded polymer composite plate reinforced with gra-phene platelets are studied in this paper. The governing equations are derived by using principle of virtual work for a plate which is rested on Pasternak's foundation. Sinusoidal shear deformation theory is used to describe displacementfield. Four different distribution patterns are employed in our analysis. The analytical solution is presented for a functionally graded plate to investigate the influence of important parameters. The numerical results are presented to show the deflection and stress results of the problem for four employed patterns in terms of geometric parameters such as number of layers, weight fraction and two parameters of Pasternak's foundation.     

A comprehensive review on material selection for polymer matrix composites subjected to impact load

Polymer matrix composites (PMC) are extensively been used in many engineering applications. Various natural fibers have emerged as potential replacements to synthetic fibers as reinforcing materials composites owing to their fairly better mechanical properties, low cost, environment friendliness and biodegradability. Selection of appropriate constituents of composites for a particular application is a tedious task for a designer/engineer. Impact loading has emerged as the serious threat for the composites used in structural or secondary structural application and demands the usage of appropriate fiber and matrix combination to enhance the energy absorption and mitigate the failure. The objective of the present review is to explore the composite with various fiber and matrix combination used for impact applications, identify the gap in the literature and suggest the potential naturally available fiber and matrix combination of composites for future work in the field of impact loading. The novelty of the present study lies in exploring the combination of naturally available fiber and matrix combination which can help in better energy absorption and mitigate the failure when subjected to impact loading. In addition, the application of multi attributes decision making (MADM) tools is demonstrated for selection of fiber and matrix materials which can serve as a benchmark study for the researchers in future.     

复合材料层合板疲劳寿命形状参数与门槛值分析方法

复合材料性能具有较大的分散性,在表征复合材料疲劳寿命时,必须考虑分散性的影响。以M21C复合材料开孔层合板为研究对象,采用Sendeckyj等效静强度模型和随机变量函数的概率分布方法推导了复合材料层合板疲劳寿命形状参数和剩余强度形状参数的关系,通过试验和统计的方法获得了M21C复合材料开孔层合板的疲劳寿命形状参数和疲劳门槛值,对载荷放大系数以及低载截除水平的确定提供了数据支持。     

复合材料组合梁的分布参数传递函数法分析模型

应用分布参数传递函数法分析了复合材料组合梁在轴压载荷作用下的振动与稳定性问题。通过引入对偶变量，利用Ｌｅｇｒｅｎｄｒｅ 变换和Ｌａｐｌａｃｅ 变换，建立了可进入Ｈａｍ ｉｌｔｏｎ 体系的混合能量变分原理，并推导出了结构在复频域内的状态空间控制方程， 从而得到了任意边界条件下组合梁振动与稳定性问题的传递函数精确解。分析了一阶和高阶横向剪切变形、转动惯量、细长比、材料各向异性等多种因素对组合梁固有频率和屈曲载荷的影响。文中最后给出了数值算例， 验证了本方法的有效性和适应性。     

偏磷酸铝在Cf/AL 复合材料中的应用

以高模高强石墨纤维Ｍ４０Ｊ增强铝基复合材料为研究对象,研究了真空液相压渗工艺中,偏磷酸铝粘接剂对纤维预制件抗压性能及复合材料力学性能的影响。结果表明：偏磷酸铝的含量、Ａｌ／Ｐ原子比及处理温度对预制件的抗压性能均有显著影响,加入５％偏磷酸铝粘接剂溶液的预制件,经５００°Ｃ处理后的抗压性能满足压渗要求,纤维保持了较好的平直度及分布均匀性,所制备的复合材料抗拉强度大于５００ＭＰａ,抗弯强度大于８００ＭＰａ     

数据流模型机SDS-l 的实现

文中全面地介绍了数据流模型机SDS-1的特点和实现方法。SDS-1模型机是一种同步和异步相结合、数据流和控制流相结合的数据流模型机,它能开发复合函数级的并行性。该模型机在Intel86/310微机和8个Intel86/12单板机组成的多机系统上实现,达到了80年代初国际先进水平。